Main page » LED DMX 512 Controller » T-1000S SD Card LED IC Pixel Controller 3-CH RGB Strip LPD6803 WS2801 WS2811
















T-1000S SD Card LED IC Pixel Controller 3-CH RGB Strip LPD6803 WS2801 WS2811
T-1000S 256M SD Card LED Pixel Controller RGB Stripe
1.T-1000S System features
1. 32~256 Gray level,Support software Gamma correction
2. Support the rules and special-shaped handle
3. Single-port output,can support 2048 pixels
4. Off-line (SD Card) control, play back content stored in the SD card
5. T-1000S store a maximum of 16 programs,copy multiple files to the SD card in order, after formatting the SD card as “FAT” format
6. The program must be named in orders . just as :00_1.led, 01_1.led, 02_1.led
7. Compatible with single line or double line chips
NOTE:
1. When T-1000S controller control less than 512 lamps the frame rate can reach 30fps
When T-1000S control more than 512 lamps and less than 2048 lamps the frame rate will slow down automatically
2. T-1000S must use the new software LedEdit 2012 or higher
2. Support chips:

3. Definition of printing:
For the TTL (SPI) signal, the controller signal ground must connect to the LED ground directly
4. Mode of connection
Multiple T-1000S controllers can be cascaded together and work synchronously.
1. T-1000S one TTL(SPI) signal and one RS485 signal port output,can control 2048 pixels/lamps
2. When the chip for LED is single line chip just with data, then just need to be connected with DAT and GND of the controller
If the chip for LED is double line chip with DAT and CLK, then need to be connected with DAT, CLK, and GND of the controller
3. If you need to use RS485 signal you need to connect controller A interface with LED lamps A (DMX+), controller B interface with LED lamps B(DMX-),
4. If you need to control a new IC type by the controller, software code mode is:T-1000-IC model.
5. Name of the program:(The rule of how to name the programs:)
The Name for NO.1 Controller:
“00_1.led” --------- NO.1 program for No.1 controller
“01_1.led” --------- NO.2 program for No.1 controller
“02_1.led” --------- NO.3 program for No.1 controller
“15_1.led” --------- NO.16 program for No.1 controller
The Name for NO.2 Controller:
“00_2.led” --------- NO.1 program for No.2 controller
“01_2.led” --------- NO.2 program for No.2 controller
“02_2.led” --------- NO.3 program for No.2 controller
“15_2.led” --------- NO.4 program for No.2 controller
6. Special parameters
Memory card:
Type: SD card(suggest using high-speed SD card)
Capacity: 128MB ~ 2GB
Format: FAT
Store file: *.led
Physical parameters:
Working temperature: -30 ~ 85 degree
Working Voltage: DC5V/DC7.5-24V
Working Power: 1W
Size: L:165mm × W:80mm × H:30mm
Weight: 0.35kg
signal Port: 3-PIN Connect Port
Note:
Before copy files to SD card ,The SD card must be formatted as FAT format
The SD card in controller can not be hot-swappable, plug the SD card every time, you must first disconnect the power supply
7. Trouble shooting
Question 1: After power, the T-1000S ERROR indicator has been flashing without display output
answer: The ERROR indicator has been flashing means the controller did not read the card correctly, possible problems:
1. SD card is empty, with no effect file
2. The effect file in the SD card and the controller model are not match, please choose correct controller model in LedEdit and then re-create the effect file *led.
3. SD card did not format to FAT before copy effect files.
4. Please check the supply power voltage, the controller can be individually powered to exclude power reasons
5. Changing the SD card and then test to exclude the possibility of a bad SD card
Question 2: The controller is powered on, the indicator is normal, but the lamps have no effect change
Answer: The reasons for this are as follows:
1. Check if the lighting′s signal line and the controller connected correctly
2. If the TTL signal is received, the lamp and the controller must be common ground, that means connect the lighting′s and the controller′s ground together
3. Check if the model chose during making display files on the SD card match the chips used in the lighting
1.T-1000S System features
1. 32~256 Gray level,Support software Gamma correction
2. Support the rules and special-shaped handle
3. Single-port output,can support 2048 pixels
4. Off-line (SD Card) control, play back content stored in the SD card
5. T-1000S store a maximum of 16 programs,copy multiple files to the SD card in order, after formatting the SD card as “FAT” format
6. The program must be named in orders . just as :00_1.led, 01_1.led, 02_1.led
7. Compatible with single line or double line chips
NOTE:
1. When T-1000S controller control less than 512 lamps the frame rate can reach 30fps
When T-1000S control more than 512 lamps and less than 2048 lamps the frame rate will slow down automatically
2. T-1000S must use the new software LedEdit 2012 or higher
2. Support chips:

3. Definition of printing:
For the TTL (SPI) signal, the controller signal ground must connect to the LED ground directly
4. Mode of connection
Multiple T-1000S controllers can be cascaded together and work synchronously.
1. T-1000S one TTL(SPI) signal and one RS485 signal port output,can control 2048 pixels/lamps
2. When the chip for LED is single line chip just with data, then just need to be connected with DAT and GND of the controller
If the chip for LED is double line chip with DAT and CLK, then need to be connected with DAT, CLK, and GND of the controller
3. If you need to use RS485 signal you need to connect controller A interface with LED lamps A (DMX+), controller B interface with LED lamps B(DMX-),
4. If you need to control a new IC type by the controller, software code mode is:T-1000-IC model.
5. Name of the program:(The rule of how to name the programs:)
The Name for NO.1 Controller:
“00_1.led” --------- NO.1 program for No.1 controller
“01_1.led” --------- NO.2 program for No.1 controller
“02_1.led” --------- NO.3 program for No.1 controller
“15_1.led” --------- NO.16 program for No.1 controller
The Name for NO.2 Controller:
“00_2.led” --------- NO.1 program for No.2 controller
“01_2.led” --------- NO.2 program for No.2 controller
“02_2.led” --------- NO.3 program for No.2 controller
“15_2.led” --------- NO.4 program for No.2 controller
6. Special parameters
Memory card:
Type: SD card(suggest using high-speed SD card)
Capacity: 128MB ~ 2GB
Format: FAT
Store file: *.led
Physical parameters:
Working temperature: -30 ~ 85 degree
Working Voltage: DC5V/DC7.5-24V
Working Power: 1W
Size: L:165mm × W:80mm × H:30mm
Weight: 0.35kg
signal Port: 3-PIN Connect Port
Note:
Before copy files to SD card ,The SD card must be formatted as FAT format
The SD card in controller can not be hot-swappable, plug the SD card every time, you must first disconnect the power supply
7. Trouble shooting
Question 1: After power, the T-1000S ERROR indicator has been flashing without display output
answer: The ERROR indicator has been flashing means the controller did not read the card correctly, possible problems:
1. SD card is empty, with no effect file
2. The effect file in the SD card and the controller model are not match, please choose correct controller model in LedEdit and then re-create the effect file *led.
3. SD card did not format to FAT before copy effect files.
4. Please check the supply power voltage, the controller can be individually powered to exclude power reasons
5. Changing the SD card and then test to exclude the possibility of a bad SD card
Question 2: The controller is powered on, the indicator is normal, but the lamps have no effect change
Answer: The reasons for this are as follows:
1. Check if the lighting′s signal line and the controller connected correctly
2. If the TTL signal is received, the lamp and the controller must be common ground, that means connect the lighting′s and the controller′s ground together
3. Check if the model chose during making display files on the SD card match the chips used in the lighting